In-depth insight on microbial electrochemical systems coupled with membrane bioreactors for performance enhancement: a review.

A conventional activated sludge (CAS) system has traditionally been used for secondary treatment in wastewater treatment plants. Due to the high cost of aeration and the problem of sludge treatment, researchers are developing alternatives to the CAS system. A membrane bioreactor (MBR) is a technology with higher solid-liquid separation efficiency. However, the use of MBR is limited due to inevitable membrane fouling and high energy consumption. Membrane fouling requires frequent cleaning, and MBR components must be replaced, which reduces membrane lifetime and operating costs. To overcome the limitations of the MBR system, a microbial fuel cell-membrane bioreactor (MFC-MBR) coupling system has attracted the interest of researchers. The design of the novel bioelectrochemical membrane reactor (BEMR) can effectively couple microbial degradation in the microbial electrochemical system (MES) and generate a microelectric field to reduce and alleviate membrane fouling in the MBR system. In addition, the coupling system combining an MES and an MBR can improve the efficiency of COD and ammonium removal while generating electricity to balance the energy consumption of the system. However, several obstacles must be overcome before the MFC-MBR coupling system can be commercialised. The aim of this study is to provide critical studies of the MBR, MES and MFC-MBR coupling system for wastewater treatment. This paper begins with a critical discussion of the unresolved MBR fouling problem. There are detailed past and current studies of the MES-MBR coupling system with comparison of performances of the system. Finally, the challenges faced in developing the coupling system on a large scale were discussed.

Biotic Cathode of Graphite Fibre Brush for Improved Application in Microbial Fuel Cells.

The biocathode in a microbial fuel cell (MFC) system is a promising and a cheap alternative method to improve cathode reaction performance. This study aims to identify the effect of the electrode combination between non-chemical modified stainless steel (SS) and graphite fibre brush (GFB) for constructing bio-electrodes in an MFC. In this study, the MFC had two chambers, separated by a cation exchange membrane, and underwent a total of four different treatments with different electrode arrangements (anodeǁcathode)-SSǁSS (control), GFBǁSS, GFBǁGFB and SSǁGFB. Both electrodes were heat-treated to improve surface oxidation. On the 20th day of the operation, the GFBǁGFB arrangement generated the highest power density, up to 3.03 W/m3 (177 A/m3), followed by the SSǁGFB (0.0106 W/m3, 0.412 A/m3), the GFBǁSS (0.0283 W/m3, 17.1 A/m3), and the SSǁSS arrangements (0.0069 W/m-3, 1.64 A/m3). The GFBǁGFB had the lowest internal resistance (0.2 kΩ), corresponding to the highest power output. The other electrode arrangements, SSǁGFB, GFBǁSS, and SSǁSS, showed very high internal resistance (82 kΩ, 2.1 kΩ and 18 kΩ, respectively) due to the low proton and electron movement activity in the MFC systems. The results show that GFB materials can be used as anode and cathode in a fully biotic MFC system.

Low-cost novel clay earthenware as separator in microbial electrochemical technology for power output improvement.

A conventional reactor in microbial electrochemical technology (MET) consists of anode and cathode compartments divided by a separator, which is usually a proton exchange membrane (PEM), such as Nafion 117. In this study, a novel porous clay earthenware (NCE) was fabricated as the separator to replace the highly cost PEM. The fabrication of NCEs is with raw clay powder and starch powder that acts as a pore-forming agent at different starch powder contents (10 vol%, 20 vol%, and 30 vol%), ball-milled before hydraulically pressed to form green ceramic pellets and sintered up to 1200 °C. The highest power density of 2250 ± 21 mW/m2 (6.0 A/m2), the internal resistance of 75 ± 24 Ω and coulombic efficiency (CE) of 44 ± 21% were produced for MFC-NCE from 30 vol% starch powder content under batch mode operation. The MFC-PEM combination produced the lowest power density, CE and the highest internal resistance up to 1350 ± 17 mW/m2 (3.0 A/m2), 23 ± 15% and 326 ± 13 Ω, respectively.

Separators used in microbial electrochemical technologies: Current status and future prospects.

Microbial electrochemical technologies (METs) are emerging green processes producing useful products from renewable sources without causing environmental pollution and treating wastes. The separator, an important part of METs that greatly affects the latter's performance, is commonly made of Nafion proton exchange membrane (PEM). However, many problems have been identified associated with the Nafion PEM such as high cost of membrane, significant oxygen and substrate crossovers, and transport of cations other than protons protons and biofouling. A variety of materials have been offered as alternative separators such as ion-exchange membranes, salt bridges, glass fibers, composite membranes and porous materials. It has been claimed that low cost porous materials perform better than PEM. These include J-cloth, nylon filter, glass fiber mat, non-woven cloth, earthen pot and ceramics that enable non-ion selective charge transfer. This paper provides an up-to-date review on porous separators and plots directions for future studies.